Rubber & Plastic Products

Iron-Modified Clay Raises Oil Yield in Automotive Plastic Waste Pyrolysis

Iron-pillared clay lifted oil yields from automotive plastic waste to as high as 78.6%, but the resulting oil still exceeds diesel limits on density and viscosity.

Beatriz SalgadoOctober 14, 20265 min read7 views
A cutaway illustration of an industrial reactor breaking down automotive plastic components, with a bed of modified clay catalyst granules and a condenser collecting liquid fuel.

Pyrolysis is emerging as a route to recover fuels and chemicals from the plastics embedded in end-of-life vehicles (ELVs), where conventional recycling struggles with mixed and contaminated materials. A new study examined what happens when plastics recovered directly from automotive components — rather than from mixed shredder residue — are processed thermally and with a low-cost, iron-modified clay catalyst.

Pyrolysis works by thermally decomposing plastics at elevated temperatures in the absence of oxygen, breaking polymer chains into liquid, gaseous and solid products. Earlier work established that common automotive plastics such as low-density polyethylene (LDPE), high-density polyethylene (HDPE) and polypropylene (PP) can be converted into valuable hydrocarbons at relatively high yields. Much of that research, however, focused on automotive shredder residue — a heterogeneous mix of plastics, metals, textiles and other materials — leaving less information about how plastics taken directly from parts such as dashboards, bumpers and headlamps behave during pyrolysis.

Feedstock characterized before processing

That distinction matters because automotive plastic waste (APW) can carry mineral fillers, flame retardants, fiberglass and other additives that alter both degradation behaviour and product composition. The study set out to characterize the feedstock first and then run pyrolysis, addressing a gap the authors identified in earlier work. The material recovered directly from ELVs contained acrylonitrile butadiene styrene (ABS), HDPE and LDPE, PP, polystyrene (PS) and fiberglass, along with substantial volatile and ash fractions. Front and rear bumpers accounted for 86.6% of the sample by weight, and the fiberglass commonly used to reinforce automotive parts contributed to the relatively high ash content.

A lower-cost catalyst route

Catalysts can improve pyrolysis efficiency by accelerating reactions, shifting product distributions and potentially lowering the temperature or residence time required. Commercial zeolites have been widely studied for this purpose, but lower-cost clay-based alternatives are drawing more interest. Pillared clays modified with metals such as iron, titanium or zirconium have shown potential to raise liquid yields and influence the formation of fuel-range hydrocarbons, and iron-modified clays are particularly attractive because they may improve oil production without relying on more expensive commercial catalysts.

Instead of using bentonite clay in its original form, the researchers modified it through iron pillaring — a process that introduces iron species into the clay structure and changes characteristics such as surface acidity and pore structure that can influence pyrolysis reactions.

Yield gains, limited selectivity

The team compared thermal and catalytic pyrolysis across temperatures from roughly 350°C to 521°C and catalyst loadings of about 6% to 34% by weight, using a statistical experimental design that allowed them to evaluate the interaction between temperature and catalyst concentration.

The catalyst had a strong effect on liquid yield. Catalytic pyrolysis produced an average oil yield of about 68%, compared with 41% for thermal pyrolysis alone. The highest oil yield, 78.6%, was reached at approximately 416°C with a catalyst loading of about 24%.

Its influence on oil composition was much weaker. Thermal and catalytic pyrolysis produced similar proportions of hydrocarbons within the C8–C24 range associated with gasoline- and diesel-range compounds. In effect, the catalyst helped convert more of the plastic feedstock into liquid product but did not substantially shift that liquid toward a higher proportion of diesel-range molecules.

Temperature had a greater effect on composition. Lower pyrolysis temperatures favoured diesel-range organics, while temperatures above 450°C produced a heavier, waxier oil.

Properties close to diesel, with gaps

The resulting pyrolysis oil showed several properties comparable to those of commercial diesel. The researchers reported a calorific value of 49.85 MJ/kg, a flash point of 113°C and total aromatics of 3.55% by area — values within or comparable to the ranges specified for conventional fuels. Branched heptenes and heptanes dominated the oil, compounds also identified in earlier studies of polypropylene and automotive-plastic pyrolysis.

Not all properties met diesel specifications. Both density and viscosity exceeded the limits typically specified for diesel fuel, which the researchers attributed partly to heavier, long-chain hydrocarbon fractions remaining in the oil. Additional processing would therefore be required before the oil could be used as a diesel-range fuel. The authors suggested approaches including distillation and centrifugation, as well as optimizing reaction conditions through lower temperatures and longer residence times to reduce heavier fractions and improve fuel properties.

Toward commercial application

The study positions pyrolysis as a technically promising route for recovering value from automotive plastics, while highlighting the development still needed before the process moves toward broader commercial application. Future work could investigate different iron concentrations in the catalyst, improve reactor designs and heat transfer, and combine pyrolysis with downstream distillation to separate gasoline- and diesel-range fractions.

Improved collection and sorting of automotive plastics will also be important. Without systematic removal and classification of plastic components from end-of-life vehicles, reliable data on the volume and composition of available automotive plastic waste remain limited — information that researchers and recyclers would need to assess feedstock availability and plan potential industrial-scale pyrolysis operations.